MTS Workholding

We built the clamps
we couldn't find.

The MTS Workholding line was designed and built to solve real production problems at Metal Essence: clamping that survives aggressive cutting, second-op fixturing that holds tight without marking finished surfaces, and quick-change jaws at a fraction of OEM cost. Everything here is in daily use at Metal Essence before it reaches your floor.

Product Family

Super Clamp System

A high-force clamping system built to hold through aggressive feeds and speeds. A single Super Clamp holds two parts at once, for both first-op raw stock and second-op finished parts.

First Op: Raw Stock

Holding Raw Material

Standard configurations hold rectangular or round stock, with custom geometries available to grip extruded profiles. Faces are typically serrated for raw material to maximize bite on as-received surfaces.

Rectangular, round, or custom extruded profiles
Serrated faces for maximum grip on raw stock
Holds through heavy roughing without pulling parts
Second Op: Finished Parts

Holding Machined Parts

Second-op clamps are profiled to your part and run smooth-faced to protect finished surfaces, with full tool access around the part above the clamp.

Profiled to your part, smooth-faced to protect finish
Full clearance above the clamp for tool access all around the part
Holds two finished parts per clamp

Proven at Metal Essence

Holding power, measured in real cutting data.

800 IPM

Roughing aluminum extrusion with a 1/2" end mill at 18,000 RPM, without pulling parts out of the clamp.

450 IPM

Roughing 12L14 steel with a 1/2" end mill at 12,000 RPM, with a secure hold through the full cut.

Built to Protect Your Fixtures

Insert options keep aluminum fixtures from wearing out or losing threads over repeated setups, so the fixture lasts as long as the job does. Custom profiles are available for extruded stock.

Why Shops Use the Super Clamp

  • Maximum clamping force for aggressive material removal rates
  • Two parts held per clamp, first op or second op
  • Full tool access around the part on second-op work
  • Insert options protect aluminum fixtures from wear and thread damage
Loading parts into a second-op fixture built with MTS Super Clamps

Product Family

Mini-Clamp Family

A compact clamp system for holding on minimal material, in vise jaws or on fixture plates. Bites on as little as 0.060" of stock and scales from a single small part to long parts across a fixture plate.

A Mazak HCN-5000 machining parts held in an MTS Mini-Clamp fixture
Mini-Clamps holding 20 parts per cycle on a Mazak HCN-5000 at Metal Essence.

Solid Bite Clamp

Bites on as little as 0.060" of stock, so you give up almost no material to workholding. Use it in vise jaws or mount it to fixture plates.

It also works as a dovetail clamp. Add a simple prep cut to the raw material and the clamp locks into it the way a dovetail fixture would, giving you a dovetail-strength hold on large, heavy parts with minimal stock allowance. We've held 70 lb steel parts this way. The prep takes no special tooling: an off-the-shelf thread mill cuts it, so there is no dedicated dovetail cutter to buy.

Bites on as little as 0.060" of stock
Dovetail-style hold with surface prep, demonstrated on 70 lb steel parts
Dovetail prep uses an off-the-shelf thread mill, no special tooling
Use in vise jaws or mount directly to fixture plates

Split Bite Clamp

Delivers strong, consistent clamping force and accommodates a small range of stock-size variation. Use it to hold a single part or two parts at once.

Strong, consistent clamping force
Accommodates a small range of stock-size variation
Holds one part or two parts at once

Split Flat Clamp

A flat-faced variant that applies clamping force without biting into or marking the part surface. Ideal where flatness or finish on the clamped face matters, particularly thin aluminum aerospace parts where surface stress and distortion are unacceptable.

Scales to Part Size

For larger parts, add clamps along the length to distribute holding force and keep the part secure through the cut, from one small part in a vise to a long part across a fixture plate.

Product Line

Quick-Change Machinable Jaws

~$40/pair vs. $400–700 OEM

OEM machinable jaws typically run $400–700 per set. Ours average around $40 per pair, so soft jaws become something you machine freely for every job, instead of something you ration.

  • Change in under a minute, repeat to .0002"
  • Works with Te-Co, Chick, and Kurt vises (one-time vise modification required)
  • Standard sizes from 1-1/4" thick × 6" wide up to 1-3/4" thick × 15" wide
  • Custom sizes available, typically within a week

For a shop running four or more vises, the jaw cost difference alone is $1,400–$2,600 per set.

Jaw Variations

The quick-change system comes in several configurations for both first and second op: standard ready-to-run jaws as well as application-specific styles.

Step Jaws

Ready-to-run jaws for holding on flat surfaces, with no custom soft-jaw machining required. Available in a variety of widths and depths, with position markings for faster, more repeatable part loading.

Bite Jaws

Jaws that bite into the material for a secure hold on minimal stock, useful for first op or any setup where you want to give up as little material as possible. Several variations available.

Clearance Jaws

Relieved jaws for running a small part in the middle of the jaw while keeping access to both sides. The clearance ensures an ER16 collet holder won't hit the jaw when doing side work.

Product Line

Dovetail Fixtures

Traditional dovetail fixtures for parts where you cut a dovetail pocket into one side of the raw material and hold from that feature. Built primarily for larger aluminum plates and boxes, the dovetail lets you avoid jumping up to the next plate-stock thickness, which can mean carrying as much as a half inch of extra material you'd otherwise machine away.

  • Avoid stepping up to the next plate thickness, for less wasted stock
  • Very strong, secure hold for aggressive machining
  • Excellent part access on a horizontal mill, including back edges
  • Reach back edges with tools like back chamfer cutters
Inquire About Dovetail Fixtures

Product Line

Grid Base Plates for Tombstones

Custom grid-style base plates for Chick, Te-Co, and Kurt tombstones. These replace the vise assembly and give you a bolt-pattern grid for mounting custom fixture plates, plus a dovetail mounting pocket in the center for our dovetail fixtures. When the fixture plates are made correctly, the system repeats within .0002".

  • Fits Chick, Te-Co, and Kurt tombstones
  • Bolt-pattern grid for mounting custom fixture plates
  • Center dovetail pocket accepts our dovetail fixtures
  • Accepts fixture plates larger or smaller than the base plate itself
  • Repeats within .0002" with correctly made fixture plates
Inquire About Base Plates

Design Support

Templates and solid models to speed up your fixture design.

Designing your own fixtures around MTS Workholding? We provide design templates and solid models of our products, so your engineers can drop them straight into a fixture design instead of modeling them from scratch.

Request Templates & Models

Partner Workholding Brands

In addition to the MTS product line, we are authorized resellers for leading workholding manufacturers.

Chick Workholding Solutions logo

Chick Workholding Solutions

Tombstones, vises, and modular fixturing

Te-Co Manufacturing logo

Te-Co Manufacturing

Clamps, vises, and fixturing components

Need a Workholding Solution?

Tell us what you're holding and what machine it's going on. We'll point you to the right clamp, jaw, or fixture setup.